a80 general specifcations electrical capacity (resistive load) power level (silver): 6a @ 125v ac or 3a @ 250v ac or 3a @ 30v dc logic level (gold): 0.4va maximum @ 28v ac/dc maximum (applicable range 0.1ma ~ 0.1a @ 20mv ~ 28v) note: find additional explanation of operating range in supplement section. other ratings contact resistance: 10 milliohms maximum for silver; 20 milliohms maximum for gold insulation resistance: 1,000 megohms minimum @ 500v dc dielectric strength: 1,000v ac minimum between contacts for 1 minute minimum; 1,500v ac minimum between contacts & case for 1 minute minimum mechanical life: 50,000 operations minimum electrical life: 25,000 operations minimum nominal operating force: on-to-on position of f-to-on position single pole 3.19n 3.92n double pole 4.41n 7.06n angle of throw: 20 materials & finishes bushing : brass with nickel plating housing: stainless steel mounting bracket: steel with tin plating movable contacts: silver alloy or silver alloy with gold plating stationar y contacts: silver with silver plating or copper or brass with gold plating lamp contacts: phosphor bronze base: diallyl phthalate (ul94v-0) switch terminals: copper with silver or gold plating lamp t erminals: brass with silver or gold plating environmental data operating t emp range: C10c through +55c (+14f through +131f) humidity: 90 ~ 95% humidity for 96 hours @ 40c (104f) vibration: 10 ~ 55hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours shock: 50g (490m/s 2 ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) installation mounting torque: 1.47nm (13 lb ? in) for double nut; .67nm (6 lb ? in) for single nut soldering time & temp: wave soldering (pc version): see profle b in supplement section. manual soldering: see profle b in supplement section. note: lever must be in center position while soldering. cleaning: pc mountable device is not process sealed. hand clean locally using alcohol based solution. standards & certifications flammability standards: ul94v-0 base ul: file no. e44145 - recognized only when ordered with marking on switch. add /u to end of par t number to order ul recognized switch. single pole with synchronous circuits & single color leds & solder lug or pc recognized at 6a @ 125v ac. csa: file no. 023535_0_000 - certifed only when ordered with marking on switch. add /c to end of par t number to order csa certifed switch. all single pole with synchronous circuits & single color leds cer tifed at 6a @ 125v ac. 3/13/17 series m2100 led tipped toggles indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable rockers touch tilt a toggles www.nkkswitches.com
a81 distinctive characteristics industrys frst led illumination at tip of toggle switches. single color leds of red, yellow, and green, plus bicolor red/green, to meet varied design requirements. leds can operate independently from or synchronously with switching operation. antijamming feature to protect contacts from damage due to excessive downward force on the toggle. high torque bushing prevents the bushing from rotating or separating from the metal frame during installation. stainless steel frame resists corrosion. silver contacts are of specially composed alloy for hardness. high insulating barriers protect against crossover in double pole devices. terminals are molded in and epoxy sealed to lock out fux, dust, and other contaminants. 1,500v dielectric strength between switch contacts and case is accomplished by clinching the frame away from the terminals. actual size series m2100 led tipped toggles indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable a toggles rockers touch tilt www.nkkswitches.com
a82 typical switch ordering example 1 t m21 spdt on-none-on switch circuit synchronous led circuit in actuator circuits 2 on none on 3 on off on contact materials & ratings w silver; rated 6a @ 125v ac g gold; rated 0.4va max @ 28v ac/dc max 2 description for typical ordering example m2112tcw01 w led colors single color c red e yellow f green bicolor cf red/green terminals & mounting types 01 solder lug with threaded bushing 02 quick connect with threaded bushing 03 straight pc with threaded bushing 30 right angle pc with smooth bushing (available with gold contacts only) poles 1 spdt * 2 dpdt * available only with terminals 01, 02, 03 silver contacts with 6-amp rating solder lug terminals red led c 01 led circuits & actuator types l isolated t synchronous 1/4C40 threaded bushing threaded bushings no code 1/4C40 thread (inch) /m 6mm thread (metric) important: switches are supplied without ul & csa marking unless specifed. ul & csa recognized only when ordered with marking on the switch. specifc models, ratings, & ordering instructions are noted on the general specifcations page. series m2100 led tipped toggles indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable rockers touch tilt a toggles www.nkkswitches.com
a83 poles & circuits & led illumination model pole & throw toggle position & terminal numbers schematics down center up notes: terminal numbers are not actually on the switch. leds require an external power source. m2112 spdt on 2-3 none none on 2-1 isolated leds (see schematics) connected led terminals synchronous single col or led connected led terminals synchronous bic olor led connected led terminals on 4-6 on 4-6 red 5-6 none none none none none none on 4-6 off open green 5-4 m2113 spdt on 2-3 off open on 2-1 isolated leds (see schematics) connected led terminals synchronous single col or led connected led terminals synchronous bic olor led connected led terminals on 4-6 on 4-6 red 5-6 on 4-6 off open off open on 4-6 on 4-6 green 5-4 m2122 dpdt on 2-3 5-6 none none on 2-1 5-4 isolated leds (see schematics) connected led terminals synchronous single col or led connected led terminals synchronous bic olor led connected led terminals on 7-9 on 7-9 red 8-9 none none none none none none on 7-9 off open green 8-7 m2123 dpdt on 2-3 5-6 off open on 2-1 5-4 isolated leds (see schematics) connected led terminals synchronous single col or led connected led terminals synchronous bic olor led connected led terminals on 7-9 on 7-9 red 8-9 on 7-9 off open off open on 7-9 on 7-9 green 8-7 isolated single color led isolated bicolor led synchronous single color led synchronous bicolor led 1 34 6 2 (com) l(+) l(-) com (+) 1 34 6 2 (com) 5 green red external connectio n connected power terminals 16 79 2 (com) 34 5 l(+) l(-) led circuit 1 37 9 2 (com) 4 6 5 l(+) l(-) com (+) 1 34 9 2 (com) 5 67 8 green red external connectio n isolated single color led isolated bicolor led synchronous single color led synchronous bicolor led keyway 1 34 6 2 (com) l(+) l(-) connected power terminals connected power terminals connected power terminals led circuit led circuit led circuit 1 36 com 4 2 (com) (+) red ( ) green red green 1 34 2 (com) 5 69 com 7 (+) red ( ) green red green series m2100 led tipped toggles indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable a toggles rockers touch tilt www.nkkswitches.com
a84 led circuit, toggle, & mounting type combinations toggle with isolated led circuit l toggle with synchronous led circuit t m2112tcfw01 single color led switch does not have terminal 5. solder lug single pole threaded bushing combines with terminal codes 01, 02, & 03. smooth bushing combines with terminal code 30. max. panel thickness without locking ring .134 (3.4mm) typical switch dimensions finish: brushed aluminum standard hardw are: 2 at513h hex nuts, 1 at507h locking ring, 1 at509 lockwasher standard & optional hardware details in accessories & hardware section. max. panel thickness with standard hardware .102 (2.6mm) (12.7) .500 keyway (2.5) dia .098 (5.0) dia .197 20 1/4-40 thd (4.8) .189 (0.8) ty p .031 (4.7) ty p .185 (6.35) .250 (0.9) .035 (8.0) .315 (20.3) .799 (14.7) .579 (13.0) .512 63 2 1 5 4 (1.17) ty p .046 (2.0) ty p .079 (4.8) .189 (6.2) dia .244 (14.7) .579 (5.0) dia .197 20 1/4-40 thd (14.7) .579 (5.0) dia .197 20 single color bicolor red yellow green red/green units maximum forward current i fm 30 30 30 25 ma typical forward current i f 20 20 20 10 ma forward voltage v f 2.2 2.1 2.2 1.7/2.0 v maximum reverse voltage v rm 4 4 4 CCC v current reduction rate above 25c ?i f 0.38 0.38 0.38 0.33/0.33 ma/c ambient temperature range C10 ~ +55c led colors & specifications the electrical specifcations shown are determined at a basic temperature of 25c. led circuit is isolated and requires an external power source. if the source voltage exceeds the rated voltage, a ballast resistor is required. the resistor value can be calculated by using the formula in supplement section. cf c f e color the led is an integral part of the switch and not available separately. bicolor led is translucent white when unlit. (6.5) dia .256 (6.1) .240 (2.2) dia .087 (6.5) dia .256 (5.8) .228 (0.6) .024 series m2100 led tipped toggles indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable rockers touch tilt a toggles www.nkkswitches.com
a85 w gold over brass or copper logic level 0.4va maximum @ 28v ac/dc maximum silver over silver power level 6a @ 125v ac & 3a @ 250v ac g contact materials & ratings complete explanation of operating range in supplement section. typical switch dimensions double pole solder lug single pole only right angle pc single color led switch does not have terminal 8. m2122tcfw01 single color led switch does not have terminal 5. gold contact material only m2112tcfg30 keyway (2.5) dia .098 (5.0) dia .197 (17.5) .689 (6.35) .250 20 1/4-40 thd (4.8) .189 (0.8) ty p .031 (4.7) ty p .185 (6.35) .250 (0.9) .035 (8.0) .315 (20.3) .799 (14.7) .579 (13.0) .512 96 3 2 1 5 4 8 7 (1.17) ty p .046 (2.0) ty p .079 (4.8) ty p .189 keyway (2.5) dia .098 (5.0) dia .197 (2.9) .114 (1.4) .055 (5.1) .201 (13.0) .512 (6.2) dia .244 (14.7) .579 (16.4) .646 (3.81) .150 (7.6) .299 (1.27) ty p .050 (0.4) .016 (1.1) .043 (0.8) ty p .031 (4.7) ty p .185 (4.3) .169 (12.7) .500 12 3 45 6 series m2100 led tipped toggles indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable a toggles rockers touch tilt www.nkkswitches.com
a86 terminals solder lug with turret led terminal 01 straight pc with turret led terminal 03 right angle pc 30 optional hardware: knurled nuts, dress nuts, and on-off plates are available; see details in accessories & hardware section. single pole double pole quick connect 02 single color led & isolated bicolor led switches do not have terminal 5. standard mounting hardware at513h hexagon nut (2 per switch) material: brass with nickel plating at507h locking ring (1 per switch) material: steel with chromate over zinc at509 lockwasher (1 per switch) material: steel with chromate over zinc epoxy seal (6.35) .250 (4.8) .189 (4.8) .189 (1.17) .046 (4.0) .157 (2.0) .079 (1.1) .043 (2.0) .079 thk = (0.8) ty p .031 epoxy seal (6.35) .250 (4.8) .189 (4.8) .189 thk = (0.8) ty p .031 (1.17) ty p .046 epoxy seal (6.35) .250 (4.8) .189 (4.8) .189 thk = (0.8) ty p .031 (1.57) ty p .062 (4.7) ty p .185 (4.8) .189 (1.8) dia ty p .073 1 2 3 6 5 4 (4.8) ty p .189 (4.7) ty p .185 (1.8) dia ty p .073 1 2 3 6 5 47 8 9 (3.81) .150 (4.7) ty p .185 (1.8) dia ty p .073 1 2 3 (16.4) .646 (2.54) ty p .100 4 5 6 (9.0) .354 (1.5) .059 (8.0) .315 1/4-40 thd (1.7) .067 (0.8) .031 (0.5) .020 (6.4) dia .252 (10.2) dia .402 single pole single color led & isolated bicolor led switches do not have terminal 8. single color led & isolated bicolor led switches do not have terminal 5. led terminals only available in brass with silver plating (2.0) .079 (5.8) .229 (6.35) dia .250 (12.0) dia .472 series m2100 led tipped toggles indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable rockers touch tilt a toggles www.nkkswitches.com
|
